Mts Acumen Electrodynamic Bedienungsanleitung

MTS Acumen™ Electrodynamic Test SystemLoad Frame Site Preparation Guide100-265-565 A be certain.

Caution notices indicate the presence of a hazard with a low level of risk which, ifignored, could cause moderate or minor personal injury or equipmen

IntroductionTopics:•Introduction ...

IntroductionMTS Acumen Electrodynamic Material Test Systems are designed to operate in a laboratory or light industryenvironment. These systems are no

ResponsibilitiesTopics:•Customer Responsibilities...

Customer ResponsibilitiesIt is the customer's responsibility to have the facility ready to install the system and move the system to itsfinal tes

It is the customer's responsibility to provide suitable lifting and moving devices such as an overhead craneand forklift. MTS supplies hoist ring

Initial Operation and TrainingOnce the installation is complete, MTS performs an initial operation of the load frame and a calibration checkto ensure

Site PreparationTopics:•Site Preparation...

Site PreparationThis section describes the physical, electrical, and mechanical requirements that must be considered beforeinstalling the MTS Acumen T

Floor and Table Loading ConsiderationsOnce the final layout for your system laboratory has been developed, the dimensional and weight informationfor t

© 2013 MTS Systems Corporation. All rights reserved.Trademark InformationMTS is a registered trademark and MTS Acumen and MTS Echo are registered trad

Note:Local electrical codes supercede any information found here.Customers should use the power cord kit supplied by MTS for connecting electrical pow

Electrical DisconnectEnsure that there is access and adequate room behind the frame to allow electrical disconnection of thepower cord. Disconnect the

Acumen Test System is not on a line that can be accidentally shut off. It is recommended that the MTSAcumen Test System and the computer workstation a

TemperatureThe operating temperature range of the load frame is 5°C to 40°C (51°F to 104°F). Although the load cell orforce transducer is temperature

System SpecificationsTopics:•Load Frame Dimensions...

Load Frame DimensionsNote:Specifications subject to change without notice.26 MTS Acumen™ Electrodynamic Test SystemSystem Specifications

Load Frame SpecificationsMTS Acumen 3MTS Acumen 1DescriptionDimension26 mm (1.02 in)26 mm (1.02 in)Minimum test space height1A819 mm (32.24 in)603 mm

MTS Acumen Noise LevelNote:Specifications subject to change without notice.Noise LevelMTS Acumen 3MTS Acumen 1Noise Level47 dbA47 dbATypical769 dbA69

Electrical connections must be made by qualified personnel and conform to local codes and regulations.Local electrical codes supersede any information

ContentsTechnical Support 5How to Get Technical Support...

Site Requirements ChecklistTopics:•Site Location...

Site LocationBefore installation of the MTS Acumen system, ensure the final location meets the following requirements.• The floor and table are able t

Scheduling InstallationWhen the testing site is ready, contact your authorized MTS representative to schedule an installationappointment:www.mts.com &

Moving the FrameTopics:•Before You Begin...

Before You BeginBefore moving the load frame, ensure that:• You have suitably trained lifting and moving personnel, qualified to move heavy equipment

5. Remove the fixed wood blocks around the machine.6. Use the packing list to inventory all the boxes. Accessories can be in the container with the lo

Additional ConsiderationsTopics:•Load Unit Considerations...

Acoustics...

Load Unit ConsiderationsThe load unit is typically shipped in a horizontal position on a pallet or in a crate. Lifting and moving instructionsthat des

100-265-565 A

Technical SupportHow to Get Technical SupportStart with your manualsThe manuals supplied by MTS provide most of the information you need to use and ma

When you have more than one MTS system, the system job number identifies your system. You can findyour job number in your order paperwork.Example syst

If You Contact MTS by PhoneA Call Center agent registers your call before connecting you with a technical support specialist. The agentasks you for yo

After you callMTS logs and tracks all calls to ensure that you receive assistance for your problem or request. If you havequestions about the status o

PrefaceBefore You BeginSafety first!Before you use your MTS product or system, read and understand the safety information provided with yoursystem. Im